1. Power supply voltage: AC 220V ± 10% 50 / 60HZ
2. Adapted fuel: gas, light oil, heavy oil
3. The highest instantaneous temperature resistance at the ignition end: 1300 ℃
4. Ignition frequency: 6 to 12 times / S
5. Spark energy: 12J
1. Material: metal box
2. Volume: length × width × height = 230 × 150 × 100mm
3. Mounting hole: 3 × φ8
1, 2520 high-temperature alloy front end material; semicond high-temperature material.
2. The outer diameter of the conventional ignition rod is Φ16, the mounting thread is M18 × 1.5, the outer diameter, length, and connection method of the ignition rod in special cases can be customized according to user requirements.
3. The ignition cable is a special ignition cable, and the length is supplied according to user requirements.
1. (1) The use occasion is a burner. The burner has a hole of Φ16.5 and is processed into a M18 × 1.5 installation thread. The ignition rod can be screwed in. The ignition end of the ignition rod is installed in the fuel injection (gas). ) 30 ~ 50mm before the mouth.
(2) If the torch is to be used in the application, the ignition rod needs to be fixed with a special ignition rod clamp, and the ignition end of the ignition rod is 100-200mm away from the diffusion opening. The ignition rod is a new structure ignition rod, and there is no need to adjust the discharge distance.
2. This series of ignition device consists of igniter box, special ignition cable and ignition rod. When installing, connect the ignition box and the ignition rod with a special ignition cable. The power supply is 220V.AC.
1. Before the ignition, make sure that the furnace has been purged without residual flammable gas. Prevents accidents such as deflagration when starting ignition.
2. When igniting, the ignition device should be turned on first, and then injected with fuel (gas) to ignite.
3. When the igniter is used for fuel ignition, the fuel should be atomized well. If the atomization quality is too poor, the ignition success rate will be affected. After the ignition is completed, the thruster must be manually or manually exited from the flame combustion zone to ensure the life of the ignition rod.
4. When the fuel is ignited during ignition, turn off the igniter. In order to avoid burnout of internal components caused by continuous ignition for a long time, a protection module has been added inside the igniter. If the ignition is continued for 10 seconds, the ignition output will be automatically stopped, and the ignition will be resumed by turning on the ignition switch again.
5. When installing and using the ignition rod, do not drop it to prevent the insulation porcelain of the ignition rod from cracking, resulting in high voltage leakage, no ignition, etc., which seriously affects the safety and normal operation of the equipment.
Note: Under any circumstances, customers are not recommended to open the igniter box by themselves. If there is any abnormal situation, please contact our after-sales technical staff.
Ignition equipment: can reach 100% ignition success rate , can withstand high temperature of 1300 ℃, more stable performance
Fire detection equipment: research and development process to improve the reliability of equipment operation and the accuracy of detection to ensure the safety of operations
Combustion control system: more energy-efficient than traditional design, for the purpose of optimizing the combustion efficiency of the boiler , environmental protection and emission reduction
Plant 1200 square meters, 100+ production staff, to meet customer demand
With an annual output of 5,000 units, the production capacity is higher than its peers, and it can meet the needs of large orders at any time.
Complete equipment, the introduction of domestic and foreign equipment production lines, fully automated production
Free customized solutions , more suitable product recommendations
According to the actual situation of customers, provide on- site guidance installation service to make the product operate normally
24-hour online customer service, timely collect and feedback customer questions , answer questions
Xi'an Ranxin Thermal Energy Engineering Technology Co., Ltd., located in Xi'an, is a high-tech company engaged in the design, development, production, sales, installation and commissioning of electronic ignition equipment, flame detection equipment, and automatic control systems for ignition and combustion processes .